Meat slicer care and maintenance

[processhead]

samspade Which model did you get?

[samspade]

processhead I found a Bizerba HD33 on offer up for 300. Has the auto slice and 13 in blade. Got to find a sharpener now. Its huge and probably way more than I need.

[bocephus]

samspade The price was definitely right.

[samspade]

bocephus yeah I was looking for a 12 or 10 since it’s just for the house, but I couldnt not buy it for that.

[processhead]

samspade your slicer story sounds similar to mine. I won my Hobart slicer at an auction for relatively little money. It didn’t come with a sharpener either. I found the right sharpener for it on ebay for about $100 and had to purchase two new stones for it another $25.
I paid almost 4 times for the sharpener what I paid for the slicer. I sharpened the blade with it maybe twice in the last 12 years.
Like I mentioned, I usually just touch it up with a diamond hone from time to time and it is still scary-sharp.
In hind sight, I probably should have just paid to have it sharpened and skipped buying the sharpener.
I suspect the correct sharpener for your slicer will be pricey, if and when you find it. It may cost more than what you paid for that fine German slicer.

Here are some pictures of the sharpener for my Hobart slicer. It stores behind the gray door by my thumb in front of the slicer when not in use.

Different slicer models may use different sharpeners but the principal will be essentially the same

The sharpener attaches in the slot on the lower edge of the depth adjust shelf with a thumbnut.
The sharpener has two rotating abrasive stones. The stone with the bevel sharpens the back side of the blade by adjusting the depth knob while the blade is rotating under power. Note that the back edge of the blade has a bevel profile and the stone shape and angle maintains that profile.
The flat stone dresses the feather edge from the front of the blade in a similar manner. The front edge of the blade has a flat profile.

The next two pictures show how I use a diamond hone to touch up the back edge and the front edge of the blade. Again, this is done while the blade is spinning so you need to be extremely careful and pay attention to what your are doing. It only takes a couple minutes to sharpen the blade with a diamond hone.

[samspade]

processhead thanks, the replacement sharpener on this one attaches to the top of the guide tray. With the thickness dial opened all the way you attach the sharpener to the tray in the notch. Once on, you dial number one for 30 seconds the number 2 fir 3 sec. And it’s done. Simple, but $180 for the attachment. Guess it’s worth that.
Where did you get the hone? That looks quite small and might work well.

[processhead]

samspade
The one I pictured is actually made by DMT. It is a combination coarse/fine diamond sharpener that I use on knives, and just about anything that has a cutting edge.
They area available on Amazon and elsewhere. I think I may have gotten this one at Scheel’s sporting goods. The website will remove the amazon header.

[https://www.[link removed]/DMT-FWFC-Double-Diafold-Sharpener/dp/B00004WFTW/ref=sr_1_9?crid=30ZPVXOXKIYPT&keywords=DMT+diamond+sharpening+stone&qid=1640476163&sprefix=dmt+diamond+sharpening+stone%2Caps%2C164&sr=8-9](link url)

[samspade]

processhead thanks looks like I can pick that up at home depot down the street. Might serve as a stopgap untill I can afford the assembly.

[processhead]

samspade If the blade is in relatively decent condition, I suspect all you will need is the DMT sharpener.

[samspade]

processhead if you can get a close up of your blade sometime it will tell me where mine is at.

[processhead]

samspade
Here is a shot of my blade from the back side. Does your blade feel dull to the touch? The edge looks rough, but photos don’t always tell the whole story.

[cdavis]

processhead now that looks sharp.

[calldoctoday]

processhead I don’t know, that looks pretty sharp to me. I just see a wisp of steel fog on the edge & that seems pretty sharp. Maybe not polished out, which is ok, but looks pretty sharp & in good condition.

[processhead]

To be honest, all a picture really tells me is if their any major nicks or defects.
I can only judge sharpness of a cutting edge if I run my thumb over the edge of a blade or actually use it to cut something. The actual cutting edge of a blade is so small you can only really see it under magnification.

[samspade]

Ok I found that hand held hone at home depot (kinda of a tongue twister) and I’ll pick one up. About what angle do you use.

[processhead]

samspade said in Meat slicer care and maintenance:

Ok I found that hand held hone at home depot (kinda of a tongue twister) and I’ll pick one up. About what angle do you use.

First, I know you will be careful, but please wear some heavy gloves while you are sharpening.
Make sure there are no severe nicks in the blade that might catch on the sharpener.

Use a diamond sharpener with a handle long enough that will keep your hands and fingers a safe distance from the rotating blade.

Starting on the back side of the blade, use an angle slightly greater than the natural bevel edge of the blade contour. Find an area on the slicer to work that gives you good access and mobility with the sharpener.

You want the sharpener surface to make contact with a fairly small area of the blade edge. Use the red (fine) surface of the sharpener.

Run the slicer for about 20 seconds while sharpening and then shut it down and check if you have improved the edge. If the edge isn’t improved run it again for another 20 seconds while sharpening.

After you have noted improvement, you want to move to the front of the blade. The blade will have a feather edge and using the sharpener lightly on the front edge will remove the feather edge.

Hold the sharpener almost parallel against the edge and tilted just slightly to the outside. Run the slicer just a few seconds while removing the feather edge. It won’t take long. At this point the blade should be noticeably sharper.

[glen]

You can use a magic marker at a few intervals on the blade to see how well you are judging your sharpening angle to the edge.
Afterwards the marker will wipe right off with rubbing alcohol

[twilliams]

samspade I just seen in another site that they had one of the stones on backwards which made the same angle you are getting. However, they had the same style as processhead so I’m not sure how your setup could be installed backwards or one of the stones anyways. I really don’t have a clue, just passing on what I read. Hope you get it figured out.

[processhead]

glen said in Meat slicer care and maintenance:

You can use a magic marker at a few intervals on the blade to see how well you are judging your sharpening angle to the edge.
Afterwards the marker will wipe right off with rubbing alcohol

That is a good suggestion, glen

[samspade]

processhead glen thanks both of you. Looks like my home depot lied so I will be ordering one. I will update you guys when it comes in and let you know if I still have 8 fingers and two thumbs.